Controlador de Velocidade de Motor Pwm dc 1055v Visor Digital Lcd com Função de Limite de Temporização Controle Remoto 12v 24v 36v 48v

Features

Intelligent LCD screen with backlight, able to display working time, speed percentage, current mode, forward rotation, reverse state, etc.

Equipped with wireless remote control

Multiple limit modes are available

Slow start and slow stop time can be set

The upper limit and lower limit of the speed can be set

The total working time can be set.

Support two-speed control of forward rotation speed and reverse rotation speed separately

Two modes of manual and automatic are optional. Automatic mode is fully automatic forward and reverse within the set time

Touch switch to switch forward and reverse, jog acceleration and deceleration, solve the problem of traditional potentiometers

Product parameter

Input voltage: DC10-55V (the specific voltage is equal to the rated voltage of the motor)

Output voltage: linear under load

Momentary current: 50A s

Continuous current: within 30A

Forward and reverse: support for the support of the

Wireless remote control: Yes

Timing timing: Yes

Limit function: Yes

Slow start and stop: Can be set

Speed digital display: 0-100 percentage meter

Speed regulation type: flow regulation

Speed adjustment method: jog +-

Speed adjustment range: 0——100%

Control frequency: 15KHZ

Wiring type: Fence type terminal block

Support motor: brushed motor

Module size: length * height * depth 105mm*70mm*95mm

Product net weight: 275 grams

Panel opening: length*width 98mm*63mm

Installation method: Embedded

Long press theMENUbutton to turn off the backlight

If you need reverse start, press FWD/REV reverse start

Note: The input must be divided into positive and negative. The input voltage must be equal to the rated voltage of the motor (within 10-55V)

For example, the rated voltage of the motor is 12V and the voltage of the governor is 12V. The rated voltage of the motor is 36V and the voltage of the governor is 36V.

Input 220V will burn out

The wiring of the two-wire three-wire limit switch is shown in the figure below

Support normally open mechanical switch, NPN type photoelectric switch, metal proximity switch, Hall magnetic control switch

0-1-2-3-4-5-6-7-8-9-E functions are set as follows

Manual automatic mode selectionfunction 0: 1 is manual mode 2 is automatic mode The default is 1 manual mode.

Slow start time settingFunction 1: 000-100 The slow start to 100% speed time is adjustable between 0-10 seconds. The default is 1 second.

Slow stop time settingFunction 2: 000-100 The slow stop time is adjustable between 0-10 seconds. The default is 1 second.

Speed lower limit settingfunction 3: 000-080 The minimum speed is adjustable between 0-80% and less than the maximum speed setting value. The default is 0.

Speed limit settingfunction 4: 000-100 The maximum speed is adjustable between 0-100% and is greater than the minimum speed setting value. The default is 100%.

The acceleration and deceleration value settingfunction 5: 001 002 005 010 015 020 025 The speed changes 1%, 2%, 5%, 10%, 15%, 20%, 25% every time you press the plus and minus key.

Motor total running time settingFunction 6: 0 seconds minimum -999 hours 59 minutes 59 seconds maximum The default is 0 hours 0 minutes 0 seconds No timing function.

The following function 7.8.9. is the time setting in the fully automatic mode

Forward rotation time settingFunction 7: 0 seconds minimum -999 hours 59 minutes 59 seconds maximum The default is 10 seconds

Stop time settingFunction 8: 0 seconds minimum -999 hours 59 minutes 59 seconds maximum The default is 10 seconds

Reverse time settingfunction 9: 0 seconds minimum -999 hours 59 minutes 59 seconds maximum The default is 10 seconds

Limit mode selectionFunction E: E1 Infinite position Default infinite position

E2 Press to start the motor forward rotation, forward rotation to the positive limit, and the motor stops. Press the forward and reverse keys to reverse the start

E3 According to the start of the motor forward rotation, forward rotation to the positive limit motor reverse rotation, reverse rotation to the negative limit motor stop

E4 According to the starting motor forward rotation, forward rotation to positive limit, the motor reverse rotation and work cycle

Manual and automatic mode selection Press theMENUbutton 1 to display 0 Enter manual and automatic mode selection 1 is manual mode 2 is automatic mode Press the plus and minus keys to switch Press RUN/STOP to save and exit

Start-up time setting Press the MENU key 2 to enter the function 1 setting key surface Press the plus and minus keys to set the time Press RUN/STOP to save and exit (10 is 1 second, 100 is 10 seconds)

Slow stop time setting Press theMENUkey 3 times to enter the function 2 setting key surface Press the plus and minus keys to set the time Press RUN/STOP to save and exit (10 is 1 second, 100 is 10 seconds

Speed lower limit setting Press theMENUkey 4 times to enter the function 3 key surface Press the plus and minus keys to set Press RUN/STOP to save and exit

Speed limit setting Press theMENUkey 5 times to enter the function 4 key surface Press the plus and minus keys to set the size value Press RUN/STOP to save and exit

Set acceleration and deceleration values Press theMENUkey 6 times to enter the function 5 key surface Press the plus and minus keys to switch Press RUN/STOP to save and exit

Motor running time setting

Press theMENUkey 7 times to enter the function 6 key surface The default is the maximum time 0 hour 0 minute 0 second FWD/REV key switch hour minute second

Press plus or minus to adjust the hour, minute, second size Press RUN/STOP to save and exit

Function 7 Forward rotation time setting in fully automatic mode

Press theMENUkey 8 times to enter the function 7 key surface The default is the maximum time 0 hour 0 minute 10 seconds FWD/REV key switch hour minutes seconds

Press plus or minus to adjust the hour, minute, second size Press RUN/STOP to save and exit

Function 8 Stop rotation time setting in fully automatic mode

Press theMENUbutton 9 times to enter the function 8 key surface The default is the maximum time 0 hour 0 minute 0 second FWD/REV key switch hour minute second

Press plus or minus to adjust the hour, minute, second size Press RUN/STOP to save and exit

Function 9 Reverse time setting in fully automatic mode

Press theMENUkey 10 times to enter the function 9 key surface The default is the maximum time 0 hour 0 minute 10 seconds FWD/REV key switch hour minutes seconds

Press plus or minus to adjust the hour, minute, second size Press RUN/STOP to save and exit

Function E limit mode selection E1 E2 E3 E4

Press theMENUkey 11 times to enter the function E key surface, the default is E1 unlimited digits Press plus and minus switch E1 E2 E3 E4 Press RUN/STOP to save and exit

E2 function: Press to start the motor to rotate forward, to rotate to the positive limit, and the motor to stop. Press the positive and negative keys to reverse and start

E3 function: according to the starting motor forward rotation, forward rotation to positive limit motor reverse rotation, reverse rotation to reverse limit motor stop

E4 function: according to the starting motor forward rotation, forward rotation to the positive limit motor reverse rotation cycle work

Panel opening length 98 mm wide 63mm

1. Controlador de Velocidade de Motor Pwm dc – tipo de Óculos : Óculos de Leitura