Motor para a Frente e Controlador Reverso 10a com Interruptor de Controle Remoto sem Fio Pode Controlar Dois Motores Pode Ser para Portas 12v 24v dc

The following is a detailed description of the product

(1) This controller is a wireless transmitting signal, no direction limitation, you can control the device across the wall

(2) Working voltage: DC 12V Or DC 24V (Note that if your equipment is not supported by other voltages)

(3) Supported device power : can’t exceed 70W

(4) Special reminder: If you use this controller to connect two DC motors at the same time, the current of the two motors during operation cannot exceed 10A, otherwise the controller will burn. If your motor or equipment does not stop working for a long time, we recommend that the current should not exceed 5A, which is the safest.

(5) Receive sensitivity: >-105dB

(6) Relay contact capacity : 10A 250VAC | 10A 30VDC

(7) Operating frequency: 433MHz To 315MHz

(8) On the ground without any obstructions, the no load test is 100 meters.

Note: The actual application of radio products varies according to the environment. Therefore, the gap will be very large. Please pay attention before purchasing.

(9) Output mode: Relay common / normally open / normally closed; can control multiple voltage loads if flexible application

(10) Coding method: Fixed code, also known as welding code, the board and remote control coded pin need one-to-one correspondence, the status is: high level, low level, hang in the air.

(11) Note: The remote control button can only press one button at a time and cannot hold more than 2 buttons at the same time, otherwise it will interfere with each other and affect normal operation.

(12) Wireless remote control switch is a widely used wireless control device, which is intelligently controlled by microprocessor. It can be applied in garage door control, lighting control, remote control curtain, anti-theft alarm, remote control electric door and window, signal control, industrial control, In the field of motor reversing, lifting equipment, etc., remote control switch module relay contacts are independent output, which is very suitable for direct control of various loads.

The following is a detailed introduction of the connection between the controller and the motor or equipment

Before using, you need to pay attention to whether your motor or equipment is DC 12V or DC 24V

? If the motor is DC 12V, please put the plug in this position.

? If the motor is DC 24V, please put the plug in this position.

1. e Controlador Reverso 10a com Interruptor de

The following is an introduction to the two forms of use

? When the black plug-in is placed in this position, after you press the button of the remote control, the motor will start to work, after you leave the button, the motor will continue to work.

? The plug-in is placed in this position. When you press the button of the remote control, the motor works immediately, but when your hand leaves the button, the motor stops working immediately, so your hand cannot leave the button.

2. High Quality Renovação da Casa

The following is the connection picture of motor and controller

Green line: the input and output are the positive pole of the power supply

Yellow line: the input and output are the negative pole of the power supply

Note: The price of this product only sells controllers, excluding cables and motors, thank you for your understanding!

3. Renovação da Casa

The following is a connection diagram of a controller connecting two motors

Special reminder : If you use this controller to connect two DC motors at the same time, the current of the two motors during operation cannot exceed 10A, otherwise the controller will burn. If your motor or equipment does not stop working for a long time, we recommend that the current should not exceed 5A, which is the safest.

Power cannot exceed 70W

4. Controle Remoto sem Fio Pode Controlar Dois Motores Pode Ser para Portas

5. 12v 24v dc Motor para a Frente

Introduction of each part

1. M4 : Plug the jump needle ; Wiithout the jump needle

2. Plug in the jump needle is delayed, delay 3-5 seconds to jump the needle

3. This is the decoder chip

4. This is the oscillating resistance

5. Led indicator

6. Input DC 12V or 24V power supply

7. According to the rated voltage of your equipment, DC 12V or DC 24V, insert the corresponding card slot. Note that please remember this step before using your equipment or DC motor, otherwise the controller will not work properly.

8. Output

6. Cheap Controlador do Motor

The following is a picture of the controller

7. Controlador do Motor

8. e Controlador Reverso 10a com Interruptor de

9. High Quality Renovação da Casa

10. Renovação da Casa

11. Controle Remoto sem Fio Pode Controlar Dois Motores Pode Ser para Portas

12. 12v 24v dc Motor para a Frente